Trick My Warrior

[gotwarrior]

I have a warrior that is going to be taken apart and rebuilt from the ground up. I would like to no do's and don'ts when I am doing this. I am going to be riding XC. It's already has a jet kit. I have a pro circuit slip on, and some nerf bars. I am in the processe of get a new frame. So I am going to have that powder coated with my swing arm and a-arms. Any help at all would be great.

[Yak]

You're going to do some GNCC racing? Best advice I can give you is full skid plates, six ply tires, a big fat front bumper, and a nice wide grab bar for if you need it. And before you spend money to go faster, get some good shocks so you're able to go faster once the motor is built.

[gotwarrior]

I think I am going to get a PRM font bumber, Grab bar, and skid plate. Then I am going to get some used WORKS shocks with res. I will then have all 3 rebuilt at the same time. But as far as the motor I am undecided.

[DirtDevilBT]

The shocks are a great idea for xc. The tires too. But anytime you start putting on aftermarket stuff you add weight. Skid plates, 6ply tires, shocks, big bumpers, etc etc. I'd put some money into the motor before you PC the hell out of everything.

Find yourself a JE 10.75:1 piston and web .390 cam. Great low end gains. Along with other stuff, this is what I have.

[gotwarrior]

with that pistion do you have to bore it out? I was looking some kind of topend kit that was just bolt on. But I never thought about a cam.

Since it needs a gasket kit, I was going to do all of that this winter. So in a ballpark what dose it cost for the came and pistion?

[DirtDevilBT]

You don't have to bore for any piston, however it is highly recommended. If you get a stock bore piston, and your engine bore has worn down a bit, then you will not get all you can from the piston.

Get a 20 over piston, this is a very very small increase in bore size. Then take the piston and cylinder to a shop and have them bore/hone it to fit the piston. Cost is like 50 bucks I think.

The cam and piston, this being some time ago, was I think like 250. The cam you can get through Magic for 100 bucks. The piston you might be able to get at Magic too or Alba for about 135ish. Get the gaskets and your looking at about 350 with bore.

Always get a cam before you get a piston. :D

[gotwarrior]

Now with doing this am I going to have to rebuild it more often?

[DirtDevilBT]

no, the piston uses 3 rings and the cam is a low end cam that's mild on the valve train.

My warrior is awesome and doesn't have a problem with oil burning, valve train wear, or anything. Did all the work myself except the porting and boring.

My family has 2 03 warriors. Mine has work done to it, the other only has a pipe. Mine has twice the hours, yet for some reason the other smokes a little hehe.:p

[gotwarrior]

Is there just like a kit that I can buy that has all of this in one?

[DirtDevilBT]

Call up Alba, the number and ad is in DirtWheels somewhere. They have a couple warrior kits.

[krt400ex]

Originally posted by DirtDevilBT
Call up Alba, the number and ad is in DirtWheels somewhere. They have a couple warrior kits.


or u could go on albaaction.com (http://albaaction.com)

[gotwarrior]

Here is what I am starting with. The Bumper and grab bar are off because of the frame being broke.

[gotwarrior]

This is the new frame!!

[firefighterjosh]

When I had my warrior I had a ALba pipe and K&N filter and it helped alot.

[gotwarrior]

I already have a Pro Circuit pipe, K&N, and jet kit

[krt400ex]

Originally posted by gotwarrior
Is there just like a kit that I can buy that has all of this in one?


u could try FST(four stroke tech) too. they have all kinds of stuff

[gotwarrior]

Well these are some of the things that I will be needing so if anyone know's were I can get them used.
Works Shocks
PRM bumper and grab bar
Skid plate

[DirtDevilBT]

EBay for the shocks
RockyMountain for the skids and bumpers.
I like Armidillo skids, all three bikes have them.

[krt400ex]

get pro armor skids. they r amazing. i hit a big chunk of concrete, it bent my a arrm and almost sent me over the bars. it was like 2ft around and i thought for sure my sprocket and skid plate were finished... nope, not even a scratch, nothing. best thing i ever bought.;)

[gotwarrior]

I just put the A-arms on. I went ahead an put the stock shocks, and tires on so I can roll it around.

[gotwarrior]

Here is what the other one looks like at this time!

[gotwarrior]

Opps Sorry.

[gotwarrior]

What do you think about the all black?

[gotwarrior]

Just pulled the motor, and painted the swing arm and carrier. Everything seems to be going ok. I was hoping that this frame would work because of the big jump in years. I don't no yet if my carrier is going to work. When I took it apart the bolt holes work more of a 0 than a o Just a little. So I my be able to get it to work as is. But if I have to I guess I will get a new one.

[gotwarrior]

Well it rollen againg. Everything went to back together ok. But I am going to have get new carrier bolts. They were a little thin. Pre owner must have not tighted them very well, so thats way it moved side to side.

[MO-EX-RIDER]

EASIEST PART IS DONE....PAINT THOSE HUBS ALSO:p

[gotwarrior]

Paint them black or blue?

[elementryder]

blue and also paint your springs blue to

[gotwarrior]

I am not going to mess with the springs because I am get to new shocks.

[DirtDevilBT]

Looks like it's comming along well. Great looking frame, can't wait to see the motor in there and plastics on.

[MO-EX-RIDER]

need to find some raptor plastics now:D

[gotwarrior]

Thats money that I don't have. Besides I would do the Maire plastic.

[gotwarrior]

Hey if anyone has any XC works shocks that will work on my warrior, and they want to sell let me no. I think that banshee shocks will work to.

[DirtDevilBT]

Yeah, I have triple rates on my warrior and they work great, for what they are anyway. Pick some up on EBay, that's where I got mine.

FYI: I don't know for sure but I think banshee and raptor shocks are longer than the warrior ones. Might dork out the front end, lol

Nice warrior...
Is your front tires on wrong? Looks like it needs to be the other way around...

[gotwarrior]

I think so. I just put them on so I can move it around.

[gotwarrior]

Dose anyone no if blaster shocks are the same length or not?Beacuse I can find alot more plaster shocks than I can warrior shocks.

[2muchquad]

Blaster,banshee and warrior shocks will all work.the blaster shocks are maybe less than a 1/2 inch shorter but i have used all 3 before on my blaster.The raptor ones are the ones that are long.;)

[gotwarrior]

So that half of inch is not really going to make a diffrence?

Because works banshee and blaster shocks are alot easyer to find than warrior shocks.

[gotwarrior]

But I have noticed that when you are looking a shocks on ebay it says warrior/blaster and banshee/raptor.

Which one do you think work better the blaster or the banshee?

I would get banshee shocks;) (works)

[gotwarrior]

why banshee over blaster? Just wanting to no.

[gotwarrior]

Well, Here is a update...

The motor is in the shop. Getting the oil leak fixed. I waiting on him to call me to tell me if he has to bore it or not. Then when I fide that out I have to order up a piston..

Next I found shocks. I found some banshee shocks which I think should work, it should just raise it up about a 1/4 of a inch. But the only problem is that the shocks springs are powdercoated pink:D :D :D Which nothing a shock cover can't fix.

Last night I ordered up some bolts for my carrier bearing. Because the others were junk. I also order a 12th spocket.

I have been kicking around places that have the cheapest maier plastic. Ronnies Mail Order is what I came up with. But new plastic is a little ways down the line.

So now my hold up is the motor. As soon as I get everthing back together then I can worry about cosmetics.

[DirtDevilBT]

eh, running plastics is just a phase. Run it with a seat and show off the goods. lol:D

[gotwarrior]

Well I found some elkas for $300. (BRAND NEW STILL IN THE BOX) So I am going to get some money and try to get them on monday.
I think that would be way better than some used works shocks.

[DirtDevilBT]

yeah, that's a score any way you look at it.

[gotwarrior]

Well, just got the shocks in...

[gotwarrior]

Here they are on the bike.

[gotwarrior]

Here is where its at now. Its all wired up. But still no motor.

[Honda4lyphe]

dang man..looks like your rich haha, good luck on the rebuild and good look when you start mx :devil:

[pelphrey]

That thing is looking awesome..I love me some elka's...As always keep us posted.

[gotwarrior]

I am not racing MX.. XC!!!:D :D

[gotwarrior]

Well I have been looking at new plastic. I going to go with the maier race front and the stock rear.. I also think I going to go with zest orange. But I want to know if I should go with the carbon fiber hood or with a orange hood?:D

[cody_119]

yea, that black frame, and some orange plastic would look awesome. i wanna see this after its finished, why dont you look on ebay for some new plastics, they are always a little cheaper there. nice so far tho.

[ECATV Raptor]

Is the frame and what not spray painted?

[Whapt]

there is a sweet front end i found on the net you may like. I have a 99 warrior and i like your build so far.
here is the link
http://yamaha.partswarehouse.com/pages/catalogs/detail/16/107/226/22731/1/0/0/1/1/1/15/143/maier-for-yamaha-yfm350-warrior-8904.aspx

[gotwarrior]

Originally posted by cody_119
yea, that black frame, and some orange plastic would look awesome. i wanna see this after its finished, why dont you look on ebay for some new plastics, they are always a little cheaper there. nice so far tho.

I have looked on e-bay and there really ist any race plastic on there. And I watched one go for about 200 bucks more than i could get from my local dealer. And that was some plastic that was messed up.

[gotwarrior]

Originally posted by cody_119
yea, that black frame, and some orange plastic would look awesome. i wanna see this after its finished, why dont you look on ebay for some new plastics, they are always a little cheaper there. nice so far tho.

Beleive it or not it is.. I really to cheap to get it powder coated. So I resorted to the nexted best thing.. VAN SICKEL:D It is the best paint for the job.

[ECATV Raptor]

Just hope the paint doesnt chip:ermm:

[gotwarrior]

That is way I used that kind of paint. It is really thick and heavy.

And besides a little touch up never hurts anything if I have too.

[gotwarrior]

Well my motor is just now getting started on!!!:( And the guy pulled the piston out and there was a peice missing about the size of eraser. Which fine because I was going to get a new piston anways. But now he has to crack the whole thing open and try to find the piece, or see if it is even in there.

So now its going to be even longer before I get my motor back.:mad: :mad:

[Caseys 300ex]

so do u have anynew pics??

[gotwarrior]

I don't have any new pictures... I am really at a stand still because of my motor. But I did order up a PRM Summit bumper and PRM Grab bar, so that should be in sometime next week. Then I also picked up a new brake calipar off of here, which should come next week also. So when I get everything on I will be sure to post some new pictures..:D

[Caseys 300ex]

Alright sweet i love the look of ur quad already.

[400eXr1d3rZ]

Any updates?

[gotwarrior]

I should have some in the nexted few days or so... I am waiting on some parts to get in.. I am biding on some new nerfs on ebay now so I can get ride of those old DG's.

[03warriorrider]

your bike looks like its going to be awsome. i have a 2003 warrior myself and im glad to see someone making a post like this. keep us updated.

[gotwarrior]

Well I would have a very nice update, but due to parts that haven't arrived because of stupid companies.

But I do have this on order.
-PRM Summit Bummper
-PRM Grab Bar
-AC Skid Plate
-Alba Nerfs
-10.25:1 Wiseco Piston
-Gasket Kit

The motor is getting a little closer to being done. I order a case puller. So when that comes in I should be able to see if there is anything wrong down below.

[gotwarrior]

Well I finally got parts in... An of course the skid plate dosen't fit correctly.. so I going to have to do a little retro fitting.. My motor is now ready to go back together.. I have oil gasket kit and a new 10.25:1 wiseco piston...

[gotwarrior]

Prm Bumper, PRM Grab Bar, AC Skid Plate, Tag Bars, and Alba Nerfs..

[katch26]

given me good ideas for my g/f busted warrior. She races xc and had 22's....I bought her 20s and her dad *****ed about them being too small, I see most of you guys run 20s so i dont feel so bad......keep it up, looking good.

[2muchquad]

I run 20s for xc,its just about perfect as far as ground clearance and handling goes.I get too much body roll with 22s plus they tax the motor and clutch in the mud around these parts.;) 22s are good for the fronts though

[katch26]

yeah she got 22s for the front...I thought 21s would be more even but I dont think the 1 will make a difference. Thats what I thought too, I got her gncc in the 20 I was originally gonna get the razr 2s but I know theyre heavy in the 20s I imagine it would be hard on the motor and or clutch like you said. I know they come with 22s originally but theyre cheap tires and prob weigh as much as the one I got her....6 ply and all.

check this too :) ;) :)

[woodsracer144]

hey dude i just did what your doing to your warrior to my blaster, its near and much mone in it as yours butiput the blasck gloss paint on and its wearin off i dont have a belly skid so thats wore off frim riding on a grassy trail, but by my feet i wore thu the gloos and i wore thu the factory p/c and thats about all i know. what state are you runin the XC? im thinkin about racing XC but im not sure, i live in WI. let me know how things are going

[86350x]

Along with the other stuff listed, put a new D.I.D. cam chain in it. Kibble white valves, there 540 lift chrome cylicone valve springs, and stiffer(dirt digger like 15 bucks) clutch springs in it also. I went with a white brothers cam(.440 lift all around) arias 10.5 to 1 .020 over piston. Big gun complete with stepped header. and ported the stock head. Just threw on a prodesign with and run a vented lid. Used the dyno jet kit, 148 main is pretty much perfect with the stock pilot jet. middle clipp position.

Kenda klaw xc tires is what I would reccomend. Also running the works shocks. Intake and exhaust and the shocks were the best bang for your buck things.

Ive pounded on this motor for a few years now and have had no problems with anything. After break in I haven't even needed to adjust the valves. Just change the oil 3 times a season and clean the air filter, grease the chassis.

I also gear up one tooth in the front for some more topend in the open areas.

[gotwarrior]

Well, I just got the motor in today.. I haven't started it yet, because I need a new throttle cable. So I can get that intel tuesday when the shops open. Then I am going to go and order the maier race plastic...:D I should have some new pictures up tommrow..

[gotwarrior]

Well, I just got done getting everything in and and hooked up.. I have too go to the dealership tommrow to get a few things.. Then I'll start it up and let you know how it all goes..

[Ruby Soho]

the plastic that looks like the yfz?

[gotwarrior]

I am going to order that plastic tommrow.. "ZEST ORANGE" is the color that I am going with..

[blasterfreak99]

are you going to get an elka shock for the rear

[gotwarrior]

No.. It cost way to much.. So sometime I will get the stock one redone by C&D

[hondarider101]

Originally posted by gotwarrior
This is the new frame!!

Did u spay pait that frame:confused:

[krt400ex]

its comin along nice now...can't wait to see it finished...wut plastics r u puttin on it?

[gotwarrior]

Originally posted by krt400ex
wut plastics r u puttin on it?

My plastic should be here any day.. I got Zest orange maier plastic. Stock rear, YFZ front, and a carbon fiber hood.:D

[gotwarrior]

IT'S ALWAYS SOMETHING!!!!:mad:

I am still waiting on a throttle cable. An last night a turned the motor over to get the oil moving throught the motor. And when I went too put the bolt back into the top of the jug it broke off in there.. Now I have to wait to get one of them.. And now my old battery is completely junk..:mad:

[03warriorrider]

gotwarrior if your talking about the oil pressure check bolt thing i had the same thing happen to me. and of course right before a ridding trip. go figure haha

[gotwarrior]

Yup... That is what I am talking about.. So now I have to see if my buddy at the dealership can get one over nighted... I hope he can, otherwise its going to be another weekend of watching everyone else riding..:mad:

[krt400ex]

Originally posted by gotwarrior
My plastic should be here any day.. I got Zest orange maier plastic. Stock rear, YFZ front, and a carbon fiber hood.:D


very nice...tis gonna be hot

[gotwarrior]

Originally posted by krt400ex
very nice...tis gonna be hot

I really hope so.. Because plastic costs way to much.:(

[400eXr1d3rZ]

Originally posted by gotwarrior
I really hope so.. Because plastic costs way to much.:(

You could always paint it ;)

[gotwarrior]

Are you nuts?? I DON'T THINK SO... There is no way I would paint new maier plastic..:eek2:

[blasterfreak99]

i think he means your old plastic instead of buying new ones

[gotwarrior]

I already bought the new ones.

[krt400ex]

yea plastic is alot


i saw a pic of 1 in a dirtwheels mag that had mair yfz plastics and it looked sweet. it also had a carbon fiber yfz hood. urs is gonne look nice

[blasterfreak99]

got any updates yet?

[gotwarrior]

Originally posted by blasterfreak99
got any updates yet?

I started it up today.. But I am not able to ride it because of all of the ice and frezzing rain.:(

[katch26]

any new pics with the plastics on

[gotwarrior]

I haven't got my new plastic in yet... The lady from Ronnies Mail Order said that I should see sometime nexted week.

[gotwarrior]

I put some of the stock plastic back on just so I can ride tommorrow. (you don't need front fenders):D

[gotwarrior]

well I couldn't keep it clean any longer.. I took it out riding.. The ice turned into mud, and it got pretty messy pretty quick.. what was even worse was that my switch went out just a few min after the picture was taken.. So thats just something else I have to fix.. I will update as soon as I get the new plastic on.

[gotwarrior]

they sent me blaster plastic for the rear.. so its going to be a few more days for the rear..

[MO-EX-RIDER]

the good ol' troubleshooting in the f**kn cold.....it never fails with you:D :D j/k bro....get it rollin for next weekend...your 1st race:eek2: :eek2: :eek2: :eek2: :eek2: YEEAAAHHHHH!

BTW PLASTIC IS TO PRETTY TO RACE WITH...PAINT THE STOCK:D

[PolarisRider]

Well now i know im getting zest orange instead of white:D

[blasterfreak99]

dang that looks good. keep up the good work on the review

[gotwarrior]

Originally posted by PolarisRider
Well now i know im getting zest orange instead of white:D

I was kind of worried about what it would look like.. An let me tell you I was really suprized. I just wish they would have sent me the correct rear.

[yfz450inMI]

Looking good man. Does the YFZ front plastic bolt right up or did you have to do a some trimming? Curious because this might be the route I go on my warrior.

[gotwarrior]

Originally posted by yfz450inMI
Looking good man. Does the YFZ front plastic bolt right up or did you have to do a some trimming? Curious because this might be the route I go on my warrior.

When you buy the warrior race plastic from maier the send you pecies to make the stock hardware work.. It comes with some clamps and extenders to make it all work..

[yfz450inMI]

So did you buy Warrior race front fenders or YFZ front fenders? You've been calling it YFZ front fenders but it is Warrior race look fenders that look very similar to stock YFZ front fenders?

I don't care about the extenders and brackets. I want to know if stock YFZ plastic will fit, or if the Warrior race look fenders aren't truly the same dimensionally as stock YFZ fenders.

I guess I'll just have to pull off my YFZ front fenders and check for myself.

[gotwarrior]

They are look a likes:rolleyes: I really don't think yfz plastic will work on a warrior...

[krt400ex]

its looking sweet dude, i love the orange on it

[ECATV Raptor]

You should put some spacers on there to make it wider:macho It'll look awsome with em

[gotwarrior]

Now I would like to have some graphics help. I really don't know what would kit on there.

[katch26]

id keep it clean...maybe like a small sticker that says warrior. You gotta rep it man!

[Caseys 300ex]

Have your rears come in yet??

[gotwarrior]

They told me that they would be in the middle of this week.
But the old ups man hasn't came and got the box to go back yet. So if he dosn't pick it up I going to try and sell it and get some money back.

[Caseys 300ex]

oh ic

[url]url]

[gotwarrior]

Finally I got all of it on.. I am really happy with the color.

[NPelletier]

looks good, just wondering, are u getting new wheels and tires? it looks like u already have aftermarket front wheels, but i tohught u said sometihng about them.....

once again man, looks great :D

[gotwarrior]

Originally posted by NPelletier
looks good, just wondering, are u getting new wheels and tires? it looks like u already have aftermarket front wheels, but i tohught u said sometihng about them.....

once again man, looks great :D

I trying to find some xc front tires now. As far as the wheels they will stay the same intel I can come up with some cheap beadlocks:D

[Ruby Soho]

for XC fronts, i would go with the kenda klaw xcf's. there great

awsome looking warrior by the way;)

[gotwarrior]

I just found the seat cover I am going to run...

[MO-EX-RIDER]

i like this one better and the viny/plastic sides on the one you show will get some funky cracks in there and look like poop....i know from experience:eek2:

[blasterheavyB]

IT LOOKS GREAT READY TO RACE THE B-LASTER NOW!!!!!!

[Ruby Soho]

now just get some videos of you rippin it up!

[blasterheavyB]

Originally posted by blasterheavyB
IT LOOKS GREAT READY TO RACE THE B-LASTER NOW!!!!!!


Your going to need more than that fancy plastic to beat the b-laster

[gotwarrior]

Just a few additions to my bike.. I rode this weekend...Everything worked great besides YAMAHA's junk tie rodes:mad: It hooked up great with the razers in the rear..

[blasterfreak99]

loks good. wanna race:cool:

[gotwarrior]

Originally posted by blasterfreak99
loks good. wanna race:cool:

No, I already bet one blaster this week..

[woodsracer144]

im sure if he got his 240 in it he would be untouchable, where are you getin that by the way, in the woods i think a stock blaster would take alot of quads because its so tighe and not really wide and its really tiny length wise too. bu its all in the rider

[blasterfreak99]

h3ll if i know. project blaster sucks. if it wasn't for the low prices i would never shop from them. this is the second time that they have screwed me with my parts. they haven't even billed my dads account yet so who knows when it will be here:mad: :grr: :scary:

[woodsracer144]

call'em up and get on them, my uncle sent in a kx85 and they were takein forever to do it and he shiped it to texas and he lives in WI so it wasnt to cheap to ship and then the rider was goin to loretta lynns and he was luck that ryan dungie(sp) let her ride his old bike and then he called them up and got on there case and they sent it back right away and then she got it and 2 weekes later it blew up in a big race and he sent it back and didnt have to pay for it and it was down and back in about 8 days they moved fast becasue they know that he wasnt happy with them!

if you do work with some oenthey should puts around spically id its just sendin a head isnt that what your doing? or are you sendin your motor in?

[blasterfreak99]

no i bought a complete big bore kit from them. all they had to do is ship it and i ordered it last thursday and they haven't even billed my dads account yet.:mad:

[woodsracer144]

well id i was you since youdidnt send anything in right? i would call them tommrow for me its monday but it might be something different for you. buy any ways i would call and ask ifthey have one and if they could pick it up. i dont think that theres any reason fo them to take this long, do you?

[blasterfreak99]

no thats why i am pissed off. it should have been here on tuesday. it is monday for me too. i will prolly call them tomorrow

[woodsracer144]

yeah i would too, if they have a fit about it let them have it, releave your anger on them! there was guy that was slackin on me and i waspissed becasue he said what iwas doin whatsnt wrong but it was and he was being retarded.!

[krt400ex]

Originally posted by gotwarrior
I trying to find some xc front tires now. As far as the wheels they will stay the same intel I can come up with some cheap beadlocks:D


razr2 fronts are amazing. they work likea sand paddle in the snow and mud, but they hook up so well on hardpack, and the steering is alot light with them. excellent tires IMO

[gotwarrior]

I am hoping to find some razer2's.. I have some razers on the rear now and they hook up great...But, know I just need to find the fronts.

[blasterfreak99]

dennis kirk may have the highest prices(by a couple of bucks)but they have the best customer service. gauranteed in 3 days plus free shipping on all orders over $100!

http://www.exriders.com/vbb/showthread.php?s=&threadid=279991

[gotwarrior]

Originally posted by blasterfreak99
dennis kirk may have the highest prices(by a couple of bucks)but they have the best customer service. gauranteed in 3 days plus free shipping on all orders over $100!

http://www.exriders.com/vbb/showthread.php?s=&threadid=279991

I don't know what your talkin about.. But you and woodsracer144 should pm each other rather than talk on this thread about something thats not even related..

[blasterfreak99]

i am talking to you about my last post. you said you wanted to find some razr 2's and i was trying to help out. and i agree that we should pm each other or start another thread but he just started talking to me. if you want i will delete my posts. srry for the trouble.

btw what is wrong with your tie rods?

[krt400ex]

Originally posted by gotwarrior
I am hoping to find some razer2's.. I have some razers on the rear now and they hook up great...But, know I just need to find the fronts. rockymountainatv.com (http://www.rockymountainatv.com/productDetail.do;jsessionid=D4CEA491538C7AE1628450 49F644914B.webrmatv)

[krt400ex]

let me fix that go here (http://www.rockymountainatv.com/typeDetail.do;jsessionid=D4CEA491538C7AE162845049F 644914B.webrmatv?navTitle=Tires+and+Wheels&webCatId=8&webTypeId=138&navType=type)

[woodsracer144]

yeah your right im sorry i didnk think that it would be that long, i though it would be only 1 or 2 post off topic, my bad:ermm:

[MO-EX-RIDER]

im invading your post so say something now:devil:

anyways you bunny huntin' or rollin with us on sunday??? im ready to see the new zesty plastic catch a few more "wreck" cracks:blah:

[m.h.s.c.#527]

r u the one with the 400 that i met at tthe hillbilly by the way gotwarrior this next race is cancelled cuz of ice so i got first as long as i finish the march 3 race

[MO-EX-RIDER]

^^that be me..and be sure to watterproof the quad just in case, so you can finish and be class champ:D

btw the black # plates will look good with the orange

[blasterheavyB]

is the warrior going to be ready for the big race next weekend or what because i know he has not been practicing

[gotwarrior]

It will out last that honda piece of yours..:D

[blasterheavyB]

will it well i have rode mine for about four days now and nothing broke thats longer then it takes for you to breake someting

[400eXr1d3rZ]

Originally posted by gotwarrior
It will out last that honda piece of yours..:D

Just don't bend any tie-rods :rolleyes:

[blasterheavyB]

yeah because i am not letting you use my welder anymore to weld them back up :p :p :p :p :p

[gotwarrior]

The new number plates really set it off..

[blasterfreak99]

nice ;) i don't like warriors but yours is the shiznit

[old-XC-guy]

Yeah they look good, but is it the pic or is your front end out of line ?? Better install those new tie rod ends !!! When the race is over I dont want to have to tow you in !!!:D :rolleyes: I dont have the winch in my trailer yet !!

[gotwarrior]

Yeah new tie rod ends are goin on this week.. And also a new clutch cable.. Then I still have to fix my wiring problem... But once all of that is done it ready for its first race.. hopefully I will make it past the practice lap...:D :D

[m.h.s.c.#527]

yea i dont get to go

[old-XC-guy]

What are you going to do about starting if cant figure it out ?

Hey whats up with those razer 23s that you found ? I want a spare set with wheels, dont matter if their bent a little I just want them in case I slash a front tire. I will give you the money this weekend plus some gas money if you pick them up for me.

You missed a hell of a ride Sunday at flat river !! Brian told me to tell you that my over rated dampner saved my *** fro some nasty woops !!

[gotwarrior]

they are 22's not 23's.. But I want the tires .. You can get the wheels if you want.. I found some other tires on here that were 23's.. He wanted like 60 shipped..

[gotwarrior]

Well it made it through its first race.. Suprisingly I didn't brake a single thing... But the result at the end wasn't that great because of weather and riding conditions...

[gotwarrior]

I would say here is a final picture of it.. It pretty much done besides front tires and a dampner...







Before..

[gotwarrior]

After....

[gotwarrior]

Well, I just got a set of +2 ASR arms.. So here is a few new pictures..

http://www.imagestation.com/picture/sraid225/p317a2701d7899a4af75cd14c7052b218/e9a0d5e2.jpg

http://www.imagestation.com/picture/sraid225/pb679452a2c3042f7bc01c7aa861a2007/e9a0d5fe.jpg

http://www.imagestation.com/picture/sraid225/p91ea95270e3ccc0d4dd38ed6264276aa/e9a0d61d.jpg

[Justin#38]

personally i do not like warriors but this one is pretty sick

[Ruby Soho]

looks awsome, now get an axle to match those arms!

[woodsracer144]

mabie its different where you race but why are you putin +2 a-arms on whne your racing XC? around where i live and in MN in Hair scrambles were trying to keep the as narrow as we can... i dont know mabie the xc by you are different to.. im in D23 so i dont know

[SET THE STAGE]

Originally posted by woodsracer144
mabie its different where you race but why are you putin +2 a-arms on whne your racing XC? around where i live and in MN in Hair scrambles were trying to keep the as narrow as we can... i dont know mabie the xc by you are different to.. im in D23 so i dont know

+2's on a warrior would only make it about 47"... that's barely wider than a stock yfz.

[TWISTED DINLI]

that looks awesome.

[woodsracer144]

Originally posted by SET THE STAGE
+2's on a warrior would only make it about 47"... that's barely wider than a stock yfz.

i still would of kept the stock with on it.. your that much more narrower over the hole feild and then you can just go that much more faster... depending on the rider... there was a kid on a stock LTR and my buddy was on a full Mx race ready 450r and the kid onthe 450r was goin through every thing and the ltr could get past the first set of trees....

[gotwarrior]

Originally posted by woodsracer144
mabie its different where you race but why are you putin +2 a-arms on whne your racing XC? around where i live and in MN in Hair scrambles were trying to keep the as narrow as we can... i dont know mabie the xc by you are different to.. im in D23 so i dont know

Its that not that much wider than anything else out there in XC.. It could be about two inches narrow because I have the wrong offset on my front wheels... And besides my opptions are pretty small when it comes to aftermarket arms for warriors.