PDA

View Full Version : Stripped rear hub studs


PismoLocal
08-02-2006, 01:35 PM
Hey pappy I desroyed the studs on my 400ex left hand side, rear hub, are the studs removable on these hubs? You powdercoated my hubs blue for me and I was wondering if I have any other options than to buy a new hub. If I do have to buy a new hub do you have any lying around your shop some where that I can buy and have you powdercoat?
Scro
08-02-2006, 02:02 PM
The stud will press out. I think they are around 5 bucks each.
Pappy
08-02-2006, 02:18 PM
as bama said, you can replace the studs.
250x_kyle
08-02-2006, 05:44 PM
my stud cost 7 bux and all it takes to get it out is put it in a vice and pound the junk stud out
PismoLocal
08-07-2006, 03:29 PM
Can you order them from service honda? I went to the website and couldn't find a part number for them.
Sjorge450R
08-07-2006, 06:09 PM
Originally posted by PismoLocal
Can you order them from service honda? I went to the website and couldn't find a part number for them.

they are only listed for the 250r but they work on all of the hondas.
PismoLocal
08-08-2006, 09:49 AM
Thank you very much sir.
PismoLocal
08-25-2006, 03:29 PM
Ok I have finally realized after 4 days of trying to get the studs out of my hub that I dont have the proper equiptment. I pretty much destroyed the powder coat on it in the process too.

Pappy I have the new studs for the hub but i can't get the old ones out and now I need to get the hub re-powdered. If I send you my hub to get repowdered can you put the new ones in while its there and charge me for the extra labor?
Pappy
08-25-2006, 03:30 PM
Just send it over, ill take care of it. Just cover shipping
PismoLocal
08-29-2006, 10:35 AM
Hey pappy I sent out the hub with the studs on Saturday and I threw in the rear section of the shock linkage to get re-powdered trans blue as well. It is currently powdered trans red. PM me how much I owe ya and I'll pay you when your done. Thanks
Pappy
08-29-2006, 03:37 PM
Post a pic of what section of the link you need...it is easier for me to shoot one I have here and swap you


recieved your other box today also
PismoLocal
08-29-2006, 04:05 PM
Ok I sent you the part of the linkage that is circled in red. I would like it powdered trans blue.
PismoLocal
09-06-2006, 09:53 AM
Any updates.
Pappy
09-06-2006, 02:27 PM
nothing special..just working:p
PismoLocal
09-12-2006, 10:34 AM
Any idea on when my stuff will be done???:D
Pappy
09-12-2006, 05:25 PM
i should have everything done this week, just waiting on the bearing to be removed from the linkage
PismoLocal
09-12-2006, 05:32 PM
Ok just PM me with how much I owe you.
ckasper18
09-12-2006, 05:45 PM
Next time you try and remove your studs leave the hub on the axle and tip bike on the side take nut and screw on the stud till it fits flush so you dont squish the stud over grab a big hammer and give it a couple good wraps with the hammer wala out comes the stud.........
PismoLocal
09-19-2006, 03:52 PM
Any idea what day my parts will ship?:D
Pappy
09-19-2006, 04:46 PM
As soon as they press out the linkage bearing i can do the linkage. I do not have one here so it has to go through the whole process since it is already coated.

The rear hub is stripped awaiting the linkage. As far as the total, I was not planning on charging you anything but return shipping because I know how it is to damage a coated part:p