bardeenm1
07-28-2006, 11:21 AM
Okay I'm thinking of parting out my 87 r here's the list of parts shoot me a PM with offers and I'll decide ASAP if I'm parting it out.
1-87 Motor 265 runs YZ piston fully ported by CT racing. Cases have been welded down by the shifter. Case saver bolt holes have been welded and does accept bolts. Shift shaft was stripped and shifter was welded on. This motor pulls very strong mid-top end end screamer. as of last check compression is 195 (I can double check the motor is still in my r). Decked head. shifts through all gears. Has clutch update. This engine runs side by side with a cam modded Yoshi piped and dyno tuned YFZ!
2- 86 stroker motor ported by RPMZ (HB RACING?) for MX. this is on it's last bore but has just been honed needs piston and rings. This is a powerful engine smokes 450's. polished side case. no welds at all. case save bolt holes need TLC (like normal on r motors). Shifts great. shaved and decked head.
3- Full LRD adjustable Pipe awesome pipe I can't say how much better this pipe is than my previous FMF fatty.
4- 38mm keihn carb and throttle cable Cable is in used condition.
5- 36mm keihn carb machined to almost 37.5mm with cable
6- 87 frame fresh powder spring of 05 but has seen some wear and tear and frame has been tweaked by a previous owner. unnoticably during riding but when plastic is off is slightly noticable. has had lower motor mounts repaired.
7- 2 sets of complete electrical 1 from an 86 1 from an 87
8- 2x'87 front hubs
9- 2x'87 rear hubs
10- full front brake system (calipers, plus two braided lines, master cylinder) will seperate
11- full rear brake system
12. LSR +2 +1 Arms 1 ball joint isn't great but still usable Heim joints are in good shape. In used condition paint is worn off. could use a good blasting in some Powder Best strongest standard travel arms I've come across. with chrome +2 tie rods.
13. LSR Adjustable axle +2/+4
14. Black maier race plastic factor affects sticker and seat. plastics are the typical faded used black no cracks or brakes. sticker kit and seat are so so look awesome in a picture but are starting to ware iin the normal places.
14. Front 87 spindals.
15. 87 swing arm w/bearing carrier and bearing bearings new spring 05 I was planning to replace after this season again.
16. red faded gas tank
17. red oversized gas tank
18. stock steering stem
19. Head stay
20. air box with support rings
21. 87 air boot
22. Jaws bumper
23. grab bar strong I tthink AC
24. 87 foot pegs
25. 87 aluminum DG nerfs used could use new nets other than that strong.
26. works dual rate remote ressie shocks rebuilt by legacy ZPS compression adjustable.(may not sell)
27. rear shock rebuilt by Legacy
Shocks set up for 175 LB MX C class rider fronts + 2 lsr arms.
28. Baldwin rear master cylinder gaurd.
29. Baja swingarm skid plate.
30. painted gas tank cover was blue now is scratched black paint.
31. rear brake lever
and anything I may of forgot! PM ME WITH INTEREST PICS AND WITH OR ABOUT PRICES.
1-87 Motor 265 runs YZ piston fully ported by CT racing. Cases have been welded down by the shifter. Case saver bolt holes have been welded and does accept bolts. Shift shaft was stripped and shifter was welded on. This motor pulls very strong mid-top end end screamer. as of last check compression is 195 (I can double check the motor is still in my r). Decked head. shifts through all gears. Has clutch update. This engine runs side by side with a cam modded Yoshi piped and dyno tuned YFZ!
2- 86 stroker motor ported by RPMZ (HB RACING?) for MX. this is on it's last bore but has just been honed needs piston and rings. This is a powerful engine smokes 450's. polished side case. no welds at all. case save bolt holes need TLC (like normal on r motors). Shifts great. shaved and decked head.
3- Full LRD adjustable Pipe awesome pipe I can't say how much better this pipe is than my previous FMF fatty.
4- 38mm keihn carb and throttle cable Cable is in used condition.
5- 36mm keihn carb machined to almost 37.5mm with cable
6- 87 frame fresh powder spring of 05 but has seen some wear and tear and frame has been tweaked by a previous owner. unnoticably during riding but when plastic is off is slightly noticable. has had lower motor mounts repaired.
7- 2 sets of complete electrical 1 from an 86 1 from an 87
8- 2x'87 front hubs
9- 2x'87 rear hubs
10- full front brake system (calipers, plus two braided lines, master cylinder) will seperate
11- full rear brake system
12. LSR +2 +1 Arms 1 ball joint isn't great but still usable Heim joints are in good shape. In used condition paint is worn off. could use a good blasting in some Powder Best strongest standard travel arms I've come across. with chrome +2 tie rods.
13. LSR Adjustable axle +2/+4
14. Black maier race plastic factor affects sticker and seat. plastics are the typical faded used black no cracks or brakes. sticker kit and seat are so so look awesome in a picture but are starting to ware iin the normal places.
14. Front 87 spindals.
15. 87 swing arm w/bearing carrier and bearing bearings new spring 05 I was planning to replace after this season again.
16. red faded gas tank
17. red oversized gas tank
18. stock steering stem
19. Head stay
20. air box with support rings
21. 87 air boot
22. Jaws bumper
23. grab bar strong I tthink AC
24. 87 foot pegs
25. 87 aluminum DG nerfs used could use new nets other than that strong.
26. works dual rate remote ressie shocks rebuilt by legacy ZPS compression adjustable.(may not sell)
27. rear shock rebuilt by Legacy
Shocks set up for 175 LB MX C class rider fronts + 2 lsr arms.
28. Baldwin rear master cylinder gaurd.
29. Baja swingarm skid plate.
30. painted gas tank cover was blue now is scratched black paint.
31. rear brake lever
and anything I may of forgot! PM ME WITH INTEREST PICS AND WITH OR ABOUT PRICES.