grude73
05-20-2006, 12:15 PM
Im selling my 86 250r, with CT Racing 350cc Pro-X engine.
1986 frame, no cracks - has a couple repairs
-4" leagers swinger, billet carrier, Durablue 2+2 Axle, New OEM Hubs
+2" leagers front end, New ASR tie-rods & ends, OEM hubs & spindles, Lonestar Swaybar
+1" Viper Stem, New Nac's Clamp, Pro-Taper SE bars
AC Propeg Nerfs, AC Bumper & Grab
PEP ZPS front shocks, PEP ZPS rebuilt rear
Race cut front fenders, Carbon hood & tank cover, Duncan Graphics
'86 cases, baldwin gears, CR250 ignition, 89 clutch update, cr500 clutch springs - no case damage
CT racing Pro-X 350cc Top end
CT Big Bore Pipe & Silencer
Keihin 38mm A/S Carb
I'm including oil, plugs, jets, gas can, oil measuring cups, new chain, 4 new sprockets (2 front 2 rear) aluminum atv stand,
O'neil jersey-pants-boots-gloves-helmet-goggles.....
Shift pants & jersey, fox gloves....- these are 1 ride old..
And whatever else I can find that has to do with the quad.....
Bike runs real strong, no oil or water leaks, doesnt overheat.
This quad is FAST, it was raced in Pro-Am & was very competitive, I spent the winter tearing it down & cleaning/painting/polishing most of it.
I replaced bearings, tie-rods, bars, grips, I had a bunch of parts powdercoated.
Im asking $3500.00 for it.
Open to trades...
Im particularly interested in...
86 through 91 Mazda RX-7
87 through 93 Mustang 5.0
Ford 302 engine & trans
Chevy 350 engine & trans
If you have any questions you can E-mail me at gman@outbackshack.com - or call me at 864-621-9419
Quad is located in Enoree SC - about 1 hour south of Charlotte.
Thanks
1986 frame, no cracks - has a couple repairs
-4" leagers swinger, billet carrier, Durablue 2+2 Axle, New OEM Hubs
+2" leagers front end, New ASR tie-rods & ends, OEM hubs & spindles, Lonestar Swaybar
+1" Viper Stem, New Nac's Clamp, Pro-Taper SE bars
AC Propeg Nerfs, AC Bumper & Grab
PEP ZPS front shocks, PEP ZPS rebuilt rear
Race cut front fenders, Carbon hood & tank cover, Duncan Graphics
'86 cases, baldwin gears, CR250 ignition, 89 clutch update, cr500 clutch springs - no case damage
CT racing Pro-X 350cc Top end
CT Big Bore Pipe & Silencer
Keihin 38mm A/S Carb
I'm including oil, plugs, jets, gas can, oil measuring cups, new chain, 4 new sprockets (2 front 2 rear) aluminum atv stand,
O'neil jersey-pants-boots-gloves-helmet-goggles.....
Shift pants & jersey, fox gloves....- these are 1 ride old..
And whatever else I can find that has to do with the quad.....
Bike runs real strong, no oil or water leaks, doesnt overheat.
This quad is FAST, it was raced in Pro-Am & was very competitive, I spent the winter tearing it down & cleaning/painting/polishing most of it.
I replaced bearings, tie-rods, bars, grips, I had a bunch of parts powdercoated.
Im asking $3500.00 for it.
Open to trades...
Im particularly interested in...
86 through 91 Mazda RX-7
87 through 93 Mustang 5.0
Ford 302 engine & trans
Chevy 350 engine & trans
If you have any questions you can E-mail me at gman@outbackshack.com - or call me at 864-621-9419
Quad is located in Enoree SC - about 1 hour south of Charlotte.
Thanks