Need R parts? Got an outragous amount of parts

[250R4EVR]

This is for all you people building your R. If ya need something for one that your building PM me. Ive got a Barn full of parts and the stuffs sitting around. About 3 250rs fully dissasembled.

* Would someone b kind and Turn this into a Stickey for a lil while. I figured that this is where People need the 250r Parts so . . .

[250-R-250]

Do you have any pics? I would be interested in some stuff. Is the majority aftermarket or stock?

[250R4EVR]

what do u want ? Anything stock besides a frame and axle i got. ive got a lotta aftermarket stuff also. Gimmie a list and ill let you know what i have

[250-R-250]

Check your pm

[250R4EVR]

1987 250r lower end: New hotrod crank kit. Lower end is tight, was all gone through. The previous owner ran the motor lose and the swinger rubed agains the rear of the motor putting a hairline crack in it. Since then i cleaned it up and JB welded it. Filled it with Oil and it seems to be holding fine. 400+shipping


1989 250r TopEnd: Brand new Bore 30 over ( 0 hours ) Brand new piston, rings, wrist pin. Brand new Gaskit Kit with extra head gaskit. Light Low end porting 275 shipped. Ive got over $210.00 of recipts for this top end.

I dont ave the break lines or the Fullbores

[Mechanix311]

Do you have a +1 stem chrome preferably? Thanks

[250R4EVR]

Sorry just stock stmes. Dont wanna sell my Laegers sorry

[250R4EVR]

top end

[vinnytrx450r]

Do you have any stock or aftermaket airboxes? Thanks and also do you have any plastic (what conditions is it in), and also do you have any shocks (not stock) thanks.
vinny t

[250R4EVR]

Ive got 3 stock air boxes. 45 shipped with carb to box boot. Got a full set of miaer white plastics. Front uncut, rear had the bottoms cut off. Looks good. NO crakcs on fronts at all. Rear has a knotch out of it in the way back. 140 shipped it its not an "overseized shipping charge"

Red Miear hood- 25

Just sold my shocks and bought these ones :) Sorry no more shocks. unless you want stock

[vinnytrx450r]

how much for just the airbox without the boots i just need the airbox and do you have pics of the plastic thanks
vinny t

[250R4EVR]

35 for the Box

Ill get Pics tomarrow

[vinnytrx450r]

do you have msn messenger or aol or yahoo?

[250R4EVR]

both . MSN fmfracer_8@hotmail.com
AOL aintsokoolaid

[250r tanner]

i need a pipe any kind or some nerf bars or front bumper

Thanks

[250R4EVR]

ive got the bumper thats on the quad in the Pic. and a PRM baja bumper 55 each shipped

[250R-Dee]

I'm looking for OEM a-arms/tie rods and a swingarm for an '86 frame.

Send me some pics to turbodee@yahoo.com of you have these items.


Oops... I also need a complete rear brake setup and a front master cylinder.

[250R4EVR]

50 for the a arms and tie rods
50 for the rear break set-up caliper needs some work. fixable
25 for the master cylinder with leaver

Will get pics tomarrow

[250R-Dee]

I'll shoot you the loot after I see the pics.

[250R4EVR]

you will get them tomarrow. . . ill post them up

do you have any pro peg nerfs?? or aftermarket shocks...front and/or back...let me know what you have

[250R4EVR]

Sorry No pro pegs. Got a set of AC standard for an 86 87
Only shocks i have anymore are a full set of stock shocks.

Pics will b on there way for everyone

[edz250r]

Have an aftermarket kickstarter?

[250R4EVR]

Sorry . . . I just got stock kickkers

Heres the pics for TRX250RJAPAN . . .

[250R4EVR]

pic 2

[250R4EVR]

TRX250RJAPAN: I'm missing the Rear breakline. If i find one ill through it in. I know i have one, but couldnt find it?
Leaver on the front rezzie is slightly bent, will find a replace ment for you also.


Airboxes

[250R4EVR]

Airboxes Have NO CRACKS anywhere them. There just a bit dusty. Id clean them up but its REALLY cold in the barn right now.

Miaer fender set
Dont have pics of the rears yet, camera card was full and have to delete stuff. NO CRACKS anywhere on the plastic

Hood was taken off to show there are NO breaks or cracks. Also have a smoothe red and blue hood if interested

[hondardr4life]

Would you happen to have an LRD headpipe?

[250R4EVR]

Nope

[hondardr4life]

How about a 38mm airstriker?

[250R4EVR]

Ive got a friend that has one. Ill have to ask him if he wants to sell it or not. Ill get back to you on the A/s

[twisted threads]

I need a stem. How much do you want for one??

[250R4EVR]

I had 2 of them. Sold one of them that i thought to be 100 perfectly straight. Got an email about a week later saying that when it arived it was Bent badly. So i sent out a replacement for free. Still havent recieved the first one i sent. As of this second i have no Stem. I'd Hook ya up if i did

[wilkin250r]

Thread is being moved to the For Sale section. I'm nice enough to leave a link, but it's being moved regardless.

Doctor's Orders.

[Googs]

pm sent