1986 Full MX race 250R

[LT250Racer609]

parts are....

stage 3 port and polish (runs on 110 octane)
all hinson clutch components
trued crank
Boyseen rad valve and carbon fiber reeds
Chrome LRD pipe and silencer
Lonestar Aluminum subframe
Maier race cut front and rear fenders (blue)
Red Fullbore radiator shrouds
Quad tech seat cover with stitched flames
Lonestar +2+1 race series chrome A-arms
-1 Chrome Lonestar swingarm
+4 chrome axcalliber Lonestar axle
Billet Lonestar anti fade axle nut
TCS ZPS front shocks with Remote rezzys
Rear TCS ZPS shock with remote rezzy
Billet PRP axle bearing carrier (twin row)
Chrome Duncan racing bumper
A.C. pro peg nerf bars
A.C. grab bar
Denton racing steering stabilizer
Billet Hinson brake pedal
Clarke red gas tank
Dura blue adjustable rear shock linkage
ITP front pro series wheels with holeshot MX tires
douglas billet ultimate rolled inner edge beadlock wheels w/ grooved turf tamers
Sunstar sprockets
D.I.D. chain
rear steel braided break lines
Front 400 EX steel braided brake lines
Dual piston front and rear brake calipers
In-Line radiator cooler
Billet Devol kick starter
Billet Exhaust hangers
PRP seat latch
PRP E-brake off plate
Wave rotor disc brakes
Lonestar antivibe fatbar handlebar clamp
, Quad Tech carbon fiber hood scoop
Lonestar +1 steering stem (Candy blue)
Hinson steering stem bearings
Nacs Racing throttle cover
Hinson air box rings
K & N air filter with outerwear
ASV front break clamp (andonized red)
Fully gusseted and powder coated baby blue frame
Acerbis pro rally 2 Handguards (CR red w/ black)
Moose Racing fatbars (Black)
DG skid plate
MSR clutch lever & break levers,
Blue and silver metallic flame graphics
38MM air stryker carb.


open to all offers and trades

[Cr85rRida]

is this a lt250r or TRX250r?? would you part it out if no one buys it as a whole?

[LT250Racer609]

its a TRX250R...and no i wouldnt part it out....want to get ride of as a whole...theres over 14,000 invested in it

[LT250Racer609]

also have an extra frame, pipes, carbs, hanlebars, shocks a-arms, rims, tires, sprockets, cylinders, clutch baskets etc....

[LT250Racer609]

here are some pic's....i currently have different graphics now however...http://www.imagestation.com/picture/sraid171/p649005996550795491384b1ebbf5b509/f3e67084.jpg http://www.imagestation.com/picture/sraid171/p6bd321bac1fc725218d6a351ee0725e7/f3e67088.jpg http://www.imagestation.com/picture/sraid171/p47bce1903e077cff935da59ceda655de/f3e67075.jpg http://www.imagestation.com/picture/sraid157/pa822d9b9eb3453e7100491d81d61e56b/f530fa28.jpg http://www.imagestation.com/picture/sraid171/p635afe72fd1fe159143a72be21e8d84b/f3e67094.jpg http://www.imagestation.com/picture/sraid171/pbb00cdbec47a0e7e6db4e6e6a96f86ec/f3e67079.jpg

[z400guy21]

ive got a 450 with a few lil extras but i also need a car which means i have no cash

[LT250Racer609]

what kind of 450 do you have??? and what would the extras be?

[z400guy21]

05 trx with wb e2 pipe rear wheel spacers itp front from with maxxis rzrs and rear stock rims with turf tamers, and a uni airfilter

[hondaquad74]

how much are you looking to get out of it . Also did you just break you wrist racing?

[LT250Racer609]

i shattered it....monday i go in for surgery to get pins and all the fun stuff....i hit a 90 foot double and ended up landing around 120 feet....when i landed i was clearly over the landing pad and from landing so hard and blew my wrist apart....

im more looking towards offers on trades....not really sure on how much i would take for it yet

[LT250Racer609]

as for the quad and the landing it took it like a champ...there is nothing wrong or bent from my crash

[hondaquad74]

THat sucks , i hit that same double and my quad landed great but i had my legs so stiff that all the muscle were tensed for about three days. Alright if you come up with a price let me know. and what season were 3rd in d3.

[LT250Racer609]

last season and this season....quad AM

do u race district 3?? did u race at hickory hill last weekend??

[LT250Racer609]

3rd in district 3 supercross at royal mountain*** i didnt really make any weekend events this year but 3

[Cr85rRida]

that one pic of the engine, your stator cover is missing two bolts, your case saver is MIA and holy sh*t how long is that tether cord lmao :eek: :p

[LT250Racer609]

ok for starters i only run 3 bolts in my stator cover for a reason...to take it off fast and clean the coils cause every 250r owner knows if you dont clean your coils, they will go bad....2nd i dont use a case saver because im always changing sprockets and i have NEVER had a problem with my chain comming off in the first place...and the teather cord is the normal pro design length....any other comments??

[hondaquad74]

Yeah i race d3 , im 3rd in points for quad am was in 2nd until today , now i got passed but should get it back if i do good next weekend back out at hickory, im going for that double again its not that bad once you decide your going for it. alright hope you have a speedy recovery. Bruce Lewis # 74

[LT250Racer609]

i kno its not bad...i did it my 1st lap in practice....then i went back and made some sprocket changes for the 1st moto and hit it again in the same gear i did it in practice in and just went so much farther....i dont kno if it was because i hooked up better or because i went down 1 tooth in my front sprocket but both times i hit it 4th pinned and the 2nd time i basically landed in the face of the table top....i will be out at hickory nexy weekend to watch my cousin race whose # 131 on the blue banshee in quad Am

[lOnEstArMx250r]

DUDE WHY OH WHY ARE YOU SELLING THAT

the qotm winner on ********** correct?

[LT250Racer609]

correct

[hondaquad74]

Oh yeah i wasnt picking on you or anything ,thats a big jump i never nutted up to untill the third lap on the 2nd moto. 131 is a nut launching that jump with a broken frame but what the hell its already gone might as well finish it . see you there

[LT250Racer609]

open to ALL offers on trades and cash.....

[lOnEstArMx250r]

Man i love ur quad haha trade for my hybrid lol

[Cr85rRida]

Originally posted by LT250Racer609
ok for starters i only run 3 bolts in my stator cover for a reason...to take it off fast and clean the coils cause every 250r owner knows if you dont clean your coils, they will go bad....2nd i dont use a case saver because im always changing sprockets and i have NEVER had a problem with my chain comming off in the first place...and the teather cord is the normal pro design length....any other comments??

yo didnt you see the second smily...i was just playing man its a sick quad. if you ever part it out let us know.

[LT250Racer609]

i dont think i could ever part it out....i have way too much invested in it

i would put a yz426 or a CRF450 motor in it before parting it

[bansheeCJ]

Trade for '02 Shee???

[LT250Racer609]

no thank you...aiming for a motocross type of quad

[LT250Racer609]

bump

[LT250Racer609]

anyone??

[LT250Racer609]

bumpppp

[Mxjunkie]

Trade for modded banshee possibly?

[LT250Racer609]

no banshee's.....thank's for the offer tho

[LT250Racer609]

anyone??

[LT250Racer609]

bump

[Brewer48]

Hey man still VERY INTERESTED in trading my '04 YFZ450 for your R!! I'm willing to make the drive from Indiana to NY to do this, all you'd have to do is be home and have the quad ready to go!! Let me know if you want to do this.... thanx!!

[LT250Racer609]

i would do the trade if there was a little more stuff done to your quad or if mine wasnt so built....

[Brewer48]

Willing to throw $500 your way to do the trade...

[LT250Racer609]

heres some updated pics on the 250R....

http://www.imagestation.com/picture/sraid188/p4eec85692689e74cfeb6ca4ff3f4afee/f22a9c82.jpg

http://www.imagestation.com/picture/sraid188/p878d589b1cd504251fc2cfb636e350d1/f22a9c7d.jpg

http://www.imagestation.com/picture/sraid188/p47a54a5f399e1459cfd87f228655372b/f22a9c73.jpg

http://www.imagestation.com/picture/sraid188/pde26d51a96c5d0b5fc71aec842a7521c/f22a9c5f.jpg

http://www.imagestation.com/picture/sraid188/p6be52e01959c3d5d9ba49f6c11fb3282/f22a9c28.jpg

[LT250Racer609]

bump

[LT250Racer609]

bumpp