*Slosh's MX TRX*

[slosh13]

Well guys it has been a long and tiresome build of this bike and a lot of things have slowed me down but everything is straightened out and shes finally done:D Just took some pics and thought I'd share with ya my ride for 05'.

http://img.photobucket.com/albums/v628/slosh13/finished1.jpg

http://img.photobucket.com/albums/v628/slosh13/finished2.jpg

http://img.photobucket.com/albums/v628/slosh13/finished3.jpg

http://img.photobucket.com/albums/v628/slosh13/finished4.jpg

[slosh13]

http://img.photobucket.com/albums/v628/slosh13/finished5.jpg

http://img.photobucket.com/albums/v628/slosh13/finished6.jpg

http://img.photobucket.com/albums/v628/slosh13/finished7.jpg

http://img.photobucket.com/albums/v628/slosh13/finished8.jpg

[slosh13]

http://img.photobucket.com/albums/v628/slosh13/finished9.jpg

http://img.photobucket.com/albums/v628/slosh13/finished10.jpg

http://img.photobucket.com/albums/v628/slosh13/finished11.jpg

http://img.photobucket.com/albums/v628/slosh13/finished12.jpg

[slosh13]

http://img.photobucket.com/albums/v628/slosh13/finished13.jpg

http://img.photobucket.com/albums/v628/slosh13/finished14.jpg

http://img.photobucket.com/albums/v628/slosh13/finished15.jpg

http://img.photobucket.com/albums/v628/slosh13/finished16.jpg

http://img.photobucket.com/albums/v628/slosh13/finished17.jpg

[trict_out]

i just got a boner...badass quad my friend:D

[4Q2]

Probably the nicest one I've seen...good job!!!!! I use to do all of Steve Kames' graphics, I noticed the one on the back of your truck, where are you located?

[slosh13]

Here is a Mod list for anyone who was interested:

Frame/Body/Chassis/Suspension/Drive:

Stock Frame and Subframe gusseted and powdercoated
Walsh A-3 a-arms
Walsh tie-rods
Walsh +2 steering stem with antivibe mounts
ARS-FX swingarm & Linkage
PEP steering stabilizer
RPM Dominator Axle
RPM Antifade locknut
Baldwin Motorsports Twinrow bearing carrier
PEP upper chain roller
Renthal Fatbar handlebars
Works Connection properch with hotstart lever
Oury Grips
AC standard nerfbars
IMS Roll Design footpegs with kickups
IMS heelguards
AC stadium bumper
AC engine skid plate
AC grab bar
Custom Axis Long travel suspension F+R compression/Rebound
Galfer F+R stainless brakelines
Hiper 4:1 10" front rims with 20" Maxxis Razr MX's
Hiper 8" with integrated hub rims with 18" MAxxis Razr MX's
Renthal sprockets
D.I.D X-ring chain
Baldwin Motorsports Pivot Bolt
Baldwin Motorsports Case Saver
Walsh Fatbar handlebar clamp
Galfer brake pads f+R
Terry Racing rear swingarm chain guide
JB Racing Emergency brake blockoff
Maier Neon yellow plastic
Quadtech graphics
Quadtech scooped hoodscoop
Quadtech rear master cylinder guard
Nac's Number plates
4-Skinz seat cover
Cycra stealth handguards

Engine

Sparks stainless full system pipe
K & N air filter
Outerwear for K & N air filter
Baldwin Motorsports MX cam
Baldwin Motorsports port/polish/ 3 angle valve job
Baldwin Motorsports Piston Kit
JH Racing CRF carb kit
Pro Design Kill switch
Vortex programmable ignition
Baldwin Motorsports wire harness mod
YZ450 crankcase breather tube
Kibble white valve springs
Titanium intake and stainless exhaust valves

Soon to come

Baldwin Motorsports Hubs
Quadtech Shockguards
Pingel Red anodized oil caps
Crank/ Counterbalancer mod

[XANDADA]

dayum....excellent!
Slosh=Mr. $ Bags

[Jersey450R]

dam, how man thousands you want to put in that thing! its nice. you coulda bought a brand new M3 though.

[redrider05]

now u need to go out n race that beast slosher...man o man that thing is nice..thought mine was nice but not to that lol later dude
jon fiscus

[parks9]

hey redrider, do you have pics of that crf450 for sale in your sig?


can you email them to yfz450mx_9@yahoo.com ?

[chris450R]

nice! that thing looks sweet. what width are you at in the front with the +3 arms and 4:1 wheels? also is your axle a +4 and what is the width on rear too?

thanks, chris

[slosh13]

I am at like 48.5" - 49" for the front and I am at like 49 3/4" for the rear. Just barely legal:devil:

[Gabriel Racing]

Originally posted by slosh13
Here is a Mod list for anyone who was interested:

Frame/Body/Chassis/Suspension/Drive:

Stock Frame and Subframe gusseted and powdercoated
Walsh A-3 a-arms
Walsh tie-rods
Walsh +2 steering stem with antivibe mounts
ARS-FX swingarm & Linkage
PEP steering stabilizer
RPM Dominator Axle
RPM Antifade locknut
Baldwin Motorsports Twinrow bearing carrier
PEP upper chain roller
Renthal Fatbar handlebars
Works Connection properch with hotstart lever
Oury Grips
AC standard nerfbars
IMS Roll Design footpegs with kickups
IMS heelguards
AC stadium bumper
AC engine skid plate
AC grab bar
Custom Axis Long travel suspension F+R compression/Rebound
Galfer F+R stainless brakelines
Hiper 4:1 10" front rims with 20" Maxxis Razr MX's
Hiper 8" with integrated hub rims with 18" MAxxis Razr MX's
Renthal sprockets
D.I.D X-ring chain
Baldwin Motorsports Pivot Bolt
Baldwin Motorsports Case Saver
Walsh Fatbar handlebar clamp
Galfer brake pads f+R
Terry Racing rear swingarm chain guide
JB Racing Emergency brake blockoff
Maier Neon yellow plastic
Quadtech graphics
Quadtech scooped hoodscoop
Quadtech rear master cylinder guard
Nac's Number plates
4-Skinz seat cover
Cycra stealth handguards

Engine

Sparks stainless full system pipe
K & N air filter
Outerwear for K & N air filter
Baldwin Motorsports MX cam
Baldwin Motorsports port/polish/ 3 angle valve job
Baldwin Motorsports Piston Kit
JH Racing CRF carb kit
Pro Design Kill switch
Vortex programmable ignition
Baldwin Motorsports wire harness mod
YZ450 crankcase breather tube
Kibble white valve springs
Titanium intake and stainless exhaust valves

Soon to come

Baldwin Motorsports Hubs
Quadtech Shockguards
Pingel Red anodized oil caps
Crank/ Counterbalancer mod



hey all that engine stuff from baldwin does that come in a package?


if it does if you woudlnt mind telling me how much you paid for the kit, you can tell on here or pm me,


and also im wondering how much it cost you to build that, im looking to build a walsh 450r to,



thanks and nice bike and good luck this year

[CdaleXtreme]

be sure and post a ride report on that rear end! ;)

[slosh13]

The ARSFX rear end is really good. I havent had a chance to ride like the Walsh Savior but the ARSFX is real plush. It really surprised me with the way it handles. Soaks up the braking bumps like they are ant hills. I am looking sometime down the road to get a Savior tho so I can have a full Walsh. The ARSFX is a nice setup, but their customer service sucks. Zbroz Racing is reall unprofessional and its like they have no idea about anything. That is the only reason why I wouldnt buy another. Oh BTW, I have a brand new front aarms and tierods from ARSFX if anyone is interested;)

[Jersey450R]

how much for the arms and rods? please pm me, thanks.

[Airik79mx]

[QUOTE]Originally posted by slosh13
[B]http://img.photobucket.com/albums/v628/slosh13/finished9.jpg

SICK!!!!!!!!!!!!!!!!!!!!!!:eek2:
Dude, that thing looks better than mine!!!!!

You race 4-Stroke A right?? 3 of my friends race that class.

[sampleez]

if ya do, do ya know brandon stout #7 in 4 stroke A? he lives pretty close to me, and he's doin dang good for his first year at the nat's

[yfz speed rider]

I noticed the JH racing decal on your tank. Where are you located? JH racing is pretty close to me. Sweet 450, definetly one of the best I have seen

[Honda]

http://img.photobucket.com/albums/v628/slosh13/finished1.jpg

Hmm, Tasty! I must say, yellow and black does look very nice together!

Great Job my friend!

[steveatv3]

prettty sick there slosh

[Jersey450R]

Yo Slosh, give us an estimate on how much you invested into that machine. I'm dying to know, lol.

Sick.

[Mxracer53]

Hey slosh i bet your 450r rips. thanks for posting pics you gave me alot of ideas for my next project.

[Cody_300ex]

Very sick 450 man! Awsome job!

[450ex]

i'm not a big chrome freak so your bike really draws me closer
color is much prettier than chrome
keep the rear end i liked it better than the savior

[Airik79mx]

Originally posted by 450ex

keep the rear end i liked it better than the savior [/B]



I 2nd that:rolleyes:

[ESrider]

That is definitely one sweet build!!

[twisted threads]

I also got to say that is one of the best looking bikes I have ever seen! Good Job!:cool:

[ramp rida 55]

nicent 450r ever. i wouldnt have done anything different myself. awesome job and taste!:eek2:

[roostin_dale]

ha, that bike is total junk. A-arms suck, shocks are beat to crap, the wheels are cheap, fenders have cracks, and the swinger is just an arsfx imitation brand. The motor wasnt really built by built by baldwin either.

No, actually im kidding, that would have to be my fav. bike ive ever seen. The thing is sick man, great work!

[slosh13]

Geeze cut me some slack on the bashin there roostin:blah: thanks again all you guys for the compliments.:D