Parting Out 86 250r Xc

[03GNCC270]

HOUSER RED LONG TRAVEL +1 a arms450

SPINDLES AND HUBS 125.00

HOUSER SWING ARM 88-89 LENGTH 400.00

HOUSER STEERING STEM +1 VIBRATION TOP
RENTHAL BARS AND MSR BARK BUSTERS 200.00

AC PRO PEGS FLAT PEGS 75.00

hinson clutch cover black cover and nacs water pump cover 400.00

ROLL DESIGN BRAKE PEDAL 60.00

STOCK RADIATOR 50.00

AIR BOX WITH UNI FILTER, CARB BOOT AND SNORKLE TUBE 50.00

stock a-arms good bushings and ball joint make offer

stock red gas tank no petcock or mounts make offer

ALL PRICES + FREIGHT
I AM PARTING OUT A COMPLETE BIKE IF THERE IS ANY THING YOU NEED NOT LISTED TELL ME AND I WILL SEE IF I STILL HAVE IT
CALL ME AT 1-800-847-3287 XT 119 WORK HOME 304-845-7533
CELL 304-639-9752

THANKS CHRIS

[03GNCC270]

ttt

[LT250Racer609]

how many bores are left on the ESR 310 cylinder?

[03GNCC270]

it has been bored once. 72.25 mm
will go up to 73.5

you can probably through a new piston and rings in it and be fine.

[03GNCC270]

I HAVE SOME HIPER BEADLOCK RINGS BRAND NEW LAYING HERE

THEY ARE BLACK

4-9" RINGS


15.00 EACH

[Cody_300ex]

Hey do you have a clutch perch and lever I could buy?

[bansheebc]

What about the rear caliper how much you need for it, let me know, can paypal it over asap

thanks

[03GNCC270]

WITH BRAIDED LINE SLAVE CYLINDER AND MASTER CYLINDER 150.00 + SHIPPING

[03GNCC270]

I HAVE A MSR RAPTOR CLUTCH LEVER AND PERCH WITH CABLE FOR 35.00 + FREIGHT

[brian350rx]

seat latch?????

[03GNCC270]

GOT A COUPLE GUYS INTERESTED IN THE WHOLE SEAT WITH IT ON IT. WILL LET YOU KNOW IF THEY DO NOT WANT IT

[bansheebc]

aH thanks for replying what about just the caliper, i have the rest

thanks

[03GNCC270]

100.00+FREIGHT FOR JUST THE CALIPER

[440exnacsracer]

front motor mounts?

[brandonpeake]

i would be interested in the shocks by themselves
shoot me a pirce and some pics of the shocks

[03GNCC270]

motor mounts go with the frame

[03GNCC270]

1200.00 + freight on the shocks they were fresh rebuild over the summer 4 races on them. set up for 165lb xc a rider. get me an email and i will get pics tonight

[brandonpeake]

a bit high on the shocks id be interested at $1000

[03GNCC270]

how about 1100.00 shipped

[brandonpeake]

let me see some pics and we can talk

[03GNCC270]

PICS ON THE WAY OF THE ELKAS

[03GNCC270]

EDITED

[bone705]

got a seat cover?

[03GNCC270]

JUST THE WHOLE SEAT

[nacs400ex]

How much for the Hinson basket and pressure plate, if your willing to part the engine. How much for airboot(carb to airbox) ?

[03GNCC270]

sorry not going to part out the trans. i am including the boot with the air box and have a couple guys interested in that will let you know.

thanks chris

[03GNCC270]

GUY BACKED OUT ON THE AXLE

[nacs400ex]

If you have a rear disc to sell I am interested. What kind, condition and price?

[03GNCC270]

THE BRAKE DISC IS A STOCK ONE NO BENDS NOT SURE HOW THICK THEY WERE FROM FACTORY BUT STILL STOPS GOOD. GET ME AN EMAIL AND I WILL SEND A PIC

[beak7707]

Can you get me pics of the ESR cylinder, send to z28lt1chevy@aol.com

[250r(quadman19)]

how much do u want for the hinson quick change cover?

[mikeboone]

I will take the ESR 310 cylinder & RPM axle as we discussed over tel Chris. Mike Boone

[03GNCC270]

CYLINDER AND AXLE SOLD.

I DO NOT HAVE ANOTHER GOOD CLUTCH COVER TO PUT ON THE MOTOR SO FOR NOW IT GOES WITH IT. UNLESS I HAVE TO START PARTING IT OUT. WILL LET YOU KNOW IF THAT HAPPENS

THANKS CHRIS

[xcyfz450]

still have beadlock rings for hipers

[bone705]

do you have an aftermarket carb? also any pics of the grab bar? if so please send to JLewicki12@yahoo.com

[nacs400ex]

Originally posted by 03GNCC270
THE BRAKE DISC IS A STOCK ONE NO BENDS NOT SURE HOW THICK THEY WERE FROM FACTORY BUT STILL STOPS GOOD. GET ME AN EMAIL AND I WILL SEND A PIC

Hendriksracing@hotmail.com, also wondering on a price.

Thanks
Craig

[mikeboone]

I am getting the RPM axle. Do I have to use an RPM carrier AND RPM swingarm with that?

[03GNCC270]

you can use any 250r or 400 ex carrier on that axle the swing arm doesn't matter either.

the carb is a 36mm pj i think the stock ones are 35mm pj

i will get all the pics tonight (grab bar, carb, and brake rotor)

[03GNCC270]

complete rear brake system is gone

[03GNCC270]

just finished tearing it down everything is ready to ship

[spinout]

if u have the anti fade hub email me a price and pics to rcs110@comcast.net,thanks

[sdxp787]

If you have Hiper beadlock rings, do you have any complete Hiper wheels? I am looking for a set of fronts, stock offset to fit a 250R. Help!!

Brent

[XCredrider]

how much for the radiator louvers..blsterracer08@aol.com

[dsheola]

Will you sell the rear beadlocks without tires? If not how much tread left on the tires?

[mikeboone]

Chris, PM me price on the complete seat with OMF latch. If you havent boxed RPM and ESR you can ship all together is fine.

[03GNCC270]

i do not have any hiper wheels left. just the rings

the tires have 1 race on them i can split them 97% tread if you want 160.00 for just the beadlocks

*******UPDATE*******

FRAME IS CRACKED
WHEN I TOOK EVERYTHING APART BOTH FRONT MOTOR MOUNTS HAVE THE START OF A CRACK GOING ON THE INSIDE WHERE YOU CAN NOT SEE IT WHEN THE PIPE IS ON. MAKE ME OFFERS

[03GNCC270]

MIKE BOONE

seat cylinder and axle left today should see them thur or fri.

[03GNCC270]

TTT

[03GNCC270]

UPDATED LIST

[03GNCC270]

TTT

[03GNCC270]

rear hubs and throttle assembly sold

[03GNCC270]

front brake system sold

[03GNCC270]

BUMP

[87250rxrider]

still have the silver fenders, ac stadium bumper, and grab bar? send pics to a250rrider38@yahoo.com
thanks,
-Ryan

[03GNCC270]

ALL PICS SENT

[03GNCC270]

front shocks are on ebay

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=4519124745

[03GNCC270]

PLASTIC AC BUMPER AND GRAB BAR SOLD

[03GNCC270]

frame is sold

[03GNCC270]

list updated

[03GNCC270]

HIPER RINGS ARE SOLD

[robyone]

can I get some pics of the houser a arms and price rojenrollison@adelphia.net...thanks

[Honda5]

do you have the bolt that goes in the rear linkage with the greese fitting in it?

[03GNCC270]

pics sent
sorry do not have that bolt already sold

[03GNCC270]

RESENT PICS.

[MX174]

still have the stock a arms? will they work on a 300ex like the 400 will? if so shoot a price

[03GNCC270]

STILL HAVE THEM I DO NOT KNOW IF THEY WILL WORK ON THERE.

50.00 SHIPPED ON THEM

REAR ELKA IS ON EBAY

[XANDADA]

looking for 250r front brake master cylinder and aftermarket ignition. If available and in good condition please shoot me a price, thanks...

[03GNCC270]

SORRY BOTH ARE ALREADY GONE

[03GNCC270]

ttt

[gagne736]

can you send me some pictures of the AC WIDE PRO PEGS WITH KICK UPS at : anthonygagne736@hotmail.com

[03GNCC270]

SORRY SOLD THOSE MONDAY JUST TOOK THEM OFF THE LIST

[03GNCC270]

front brakes are back on the market.

everything from the calipers to the lever

has stainless +1 lines and 1/2 pads 150.00

[03GNCC270]

BOTTOM END IS SOLD

STEERING BLOCK , FRAME GUARDS AND LINKAGE IS GONE.

[03GNCC270]

TOP END IS GONE

[86250rrider]

so are the omf louvers and rad guard:D

[86250rrider]

check your paypal THANKS :D

[03GNCC270]

got it says waiting for the funds to with draw will let you know when i see it go through

thanks chris

[86250rrider]

K dont know why it isnt immediate though

[86250rrider]

woo hoo fixed!:D THANKS AGAIN

[03GNCC270]

SHIPPING TODAY

[03GNCC270]

clark tank is on ebay

[03GNCC270]

bump

[86250rrider]

got the stuff,THANKS:macho

[03GNCC270]

LIST UPDATED

[03GNCC270]

coolant overflow bottle shipped you should have it monday

[03GNCC270]

pipe, front and rear tires sold.

[400lighted]

I am looking for a seat and seat latch......if so how much? Thanks, Nick.

[03GNCC270]

SORRY SEAT IS ALREADY GONE.

[03GNCC270]

top

[blasterak]

you got the stock rear shock? if so how much you want and pics too thanks

[03GNCC270]

all the shocks are gone. everything on the list is all i have left now.

[Dupontster]

Would you happen to have a rear brake caliber. If so how much and what condition is it in.

[03GNCC270]

sorry no rear just the front system

[fastest440ex]

do u still have the swinger and what condition?

[03GNCC270]

SWING ARM SOLD