Anyone with a s10 94-up and a system??

[Taco]

Where did you run your power wire through the firewall?? I'll be running 4ga. and figured maybe I could save me some time looking.

[MY450R]

i believe there are cut outs on the fire wall left hand side by the clutch/brake pedals
just peel back the carpet and they are there someplace

[quadrcr161]

also try looking around where your AC and heater comes through. they usually have some room in the rubber gromets to let it slide through. remember run your turn on lead and power cable on one side, and your RCA's on the other side so that you done get any alt whine.

[MY450R]

there may also be some on the other side but i dont know
on my s10 i used the drivers side which is where most ppl run them

[spincr4hire]

Taco,
just drill a hole.

I've done numerous stereo system installs, and thats what I always did, just remember to investigate good before you drill, usually the passenger side has the most open space for drilling.

[Taco]

Originally posted by spincr4hire
Taco,
just drill a hole.

I've done numerous stereo system installs, and thats what I always did, just remember to investigate good before you drill, usually the passenger side has the most open space for drilling. Whenever possible I try not to add holes anywhere unless they are needed. Plus its much quicker to just cut a grommet. Hehe now to throw the 15 in the ext. cab:D

[MY450R]

Originally posted by quadrcr161
also try looking around where your AC and heater comes through. they usually have some room in the rubber gromets to let it slide through. remember run your turn on lead and power cable on one side, and your RCA's on the other side so that you done get any alt whine.
yup thats the best place but i dont know if 4 gauge wires will fit thru there

[spincr4hire]

what kinda hilljack stereo you wiring up anyways? Did you get a super deal on a Kraco 1000 Watt system from wallyworld? :p
J/K

[Motoman440]

I see your finally replacing the AM radio!!! Did ya get your freakin quad fixed yet??? That's what ya otta be workin on!!!:grr:

[k2-dawg]

What next, cut the springs and lower that pimp daddy ride of yours??? :D

[MichaelS693]

i just drilled a hole:)

[Rico]

Originally posted by MichaelS693
i just drilled a hole:)

Is that gangsta talk......:devil:



Taco who'd you jack a stereo from. I know you didnt' buy it...:o

[UglyMotha™]

i believe your actually goin to put in a system in that piece of yours......... is it even worth it http://ohiomafiariders.com/v-web/bulletin/bb/images/smiles/cookoo.gif

[crap-banshee32]

when in doubt...drill another hole!

[MY450R]

are you gonna take that smack talk taco??
they are just slicing you up bud

[UglyMotha™]

taco will take anything i serve him :o

[quadrcr161]

i hope people are putting gromets in the holes the poke in the firewall, if not you will be paying for a new eletrical system and possibility burn down the truck. if its just a bare hole thesheet metal will cut the plastic insulation and arc against the metal, not good, even if you have a fuse at the battery.

[npsxtreme]

Most existing grommets are usually to small for 4 ga. You will probably have to drill a hole. If you have an automatic, there is a blank plate where the clutch would normally go through on the driver side. Look under the dash and you will probably see what I am talking about. Most amp kits come with a grommet to fit the hole you may have to drill.

[MOFO]

Originally posted by Taco
Hehe now to throw the 15 in the ext. cab:D


there's nothing like bump'in country going down the main drag in in downtown WV.... :devil: