"BLAHH"300!!
04-09-2002, 10:48 PM
I DIDN'T WRECK!! :)
not this time. this was just plain metal fatigue i guess.
ok 300ex swing-arm 2 bolts in the back to tighten the chain.
one on chain side. cracked from right about there to about mid-ways' up the little housing deal (i guess it's called)
SUXX!!!
it's spring. this stuff's not supposed to happen untill winter.
i replaced the chain, checked all my stuff out on my last wash, witch was just last week. then today we "ROLL OUT" me a timber wolf and a freind on my big-bear. just a cruise. little muddy (FACT::--YOU GET JUST AS MUDDY WITH REAR FENDER'S AND NO FRONTS'-- AS YOU DO WITH NO REAR'S AND NO FRONT'S) well we putted around for a while, showed em' what's up a few times'.
then went to a little road jump place where it's kinda like a table top with a paved "top" hit it catching just as much air as i usually do nothing major (4/5ft air's) launching over a road landing on a downslope on the other (grassy) side..then decided to head down the high-way a little way's to go up into this old BMX track (to see if there were any old jumps still out there (it's all grown up in kudzoo vines'.) they take off i give them the lead, then i start around em' "BLING" chain's off. no biggie (:huh) there's the crack i had some tool's on the "bear" and tighten'd it up but i'm still freakin' out about the crack. it's tight ride. then i hear it poppin and grindin' like it's loose. tighten it again same ole over and over all the way home..the bolt's are tight but it's the rest of the metal around it thats loose causing the
"oval-thing":confused: to turn and get loose...ahhhh
swinger's are kinda expensive..i keep lookin up at the "quadshop's" "flash" banner and seein the swing-arm pop up and i know i gotta have one....this sux...
not this time. this was just plain metal fatigue i guess.
ok 300ex swing-arm 2 bolts in the back to tighten the chain.
one on chain side. cracked from right about there to about mid-ways' up the little housing deal (i guess it's called)
SUXX!!!
it's spring. this stuff's not supposed to happen untill winter.
i replaced the chain, checked all my stuff out on my last wash, witch was just last week. then today we "ROLL OUT" me a timber wolf and a freind on my big-bear. just a cruise. little muddy (FACT::--YOU GET JUST AS MUDDY WITH REAR FENDER'S AND NO FRONTS'-- AS YOU DO WITH NO REAR'S AND NO FRONT'S) well we putted around for a while, showed em' what's up a few times'.
then went to a little road jump place where it's kinda like a table top with a paved "top" hit it catching just as much air as i usually do nothing major (4/5ft air's) launching over a road landing on a downslope on the other (grassy) side..then decided to head down the high-way a little way's to go up into this old BMX track (to see if there were any old jumps still out there (it's all grown up in kudzoo vines'.) they take off i give them the lead, then i start around em' "BLING" chain's off. no biggie (:huh) there's the crack i had some tool's on the "bear" and tighten'd it up but i'm still freakin' out about the crack. it's tight ride. then i hear it poppin and grindin' like it's loose. tighten it again same ole over and over all the way home..the bolt's are tight but it's the rest of the metal around it thats loose causing the
"oval-thing":confused: to turn and get loose...ahhhh
swinger's are kinda expensive..i keep lookin up at the "quadshop's" "flash" banner and seein the swing-arm pop up and i know i gotta have one....this sux...