T-9 Pro Series Beadlock 4+1

[Silverfox@C&DRacing]

My distributor sent me the wrong offset so instead of trying to exchange them I'll offer them for $125 each they retail for $149 each. These are 10x5 4/144 4+1 offset

[Silverfox@C&DRacing]

another pic

[Silverfox@C&DRacing]

last one

[Silverfox@C&DRacing]

bump

[gump]

boy i really need those, but broke for about 2 weeks..:(
i'm running the rolled edge wheels right now, 4+1 are hard to come by

[southbeach14]

Originally posted by Silverfox@C&DRacing
My distributor sent me the wrong offset so instead of trying to exchange them I'll offer them for $125 each they retail for $149 each. These are 10x5 4/144 4+1 offset


wil they fit my yfz-450??

[Silverfox@C&DRacing]

sorry your yfz is a 4/156 bolt pattern

[yz400fer69]

Hello,
I am pretty new to quads and was just wondering what the offset numbers stand for? I see them alot and am confused what the numbers mean... (Ie: 4+1)

Thanks
Dave

[gump]

4= 4 inches to the center of the wheel from the inside, and 1= 1 inch to the center from the outside.. i run plus 1 a arms and use 4+1 offset wheels so i won't really be wider than i was.. stock offset is 3+2, so i'm really wider but not when i put the wheels on.. i know it's confusing and i thought i wasted money until i got used to this setup, then rode a stocker again.. better handeling and turning at high speed, plus i race woods and you don't want to be wide..
correction not the center of the wheel, where the wheel bolts up to the hub.. is it any clearer now??

[yz400fer69]

OK, so if I understood that correctly, a 4-1 offset wheel would put me an inch narrower on both sides with the stock arms?

I ride desert and woods and would like to be a little wider for obvious reasons and am looking for a new set of rims (front and rear).

Do I want to buy the offset for the rears and fronts?

Thanks
Dave

[gump]

i just edited my post.. the wheel is the same width as stock just different where it bolts up.. just doesn't stick out as far as stock would... 4+1 sticks out 1 inch and 3+2 sticks out 2 inches

[gump]

you would need a longer axle to widing the rear

[yz400fer69]

Lol so a 4-1 would make me one inch narrower?

Is it a "rule of thumb" or anything like that to stay even on the front and rear... If I go +1 up front should I go +1 on the rear as well?

Thanks
Dave

[yz400fer69]

Oh ok

Thanks for your help.

Dave

[gump]

4+1 will make you shorter with stock arms, by allmost 2 inches and you don't want that. woods riding you don't want the rear any wider, and going shorter will make it handle like chit, only use the 4+1 if you run +1 arms..
like helping people no prob, i went through all this 2 years ago, but luckily i live close to santo derisi a top pro gncc rider and learned all this from him..

[Silverfox@C&DRacing]

bump

[Jersey450R]

ok wait so if i'm running my stock a-arms and want it to be wider...what should i get??? thanks

[Silverfox@C&DRacing]

if you want to be wider run a 3+2 offset

[quadcustoms]

ill take them for 250 shipped to tennessee

615 476 4134 for my card info im david

[quadracr]

Do you have any more? I am interested in set for my Z400. 250.00 shipped to 45252?
I'm unclear why you are getting rid of them. You said you run 4-1 offset and you are selling these because they were the wrong offset. These are 4-1 right?

[Silverfox@C&DRacing]

Originally posted by quadracr
Do you have any more? I am interested in set for my Z400. 250.00 shipped to 45252?
I'm unclear why you are getting rid of them. You said you run 4-1 offset and you are selling these because they were the wrong offset. These are 4-1 right?

they were for a customer and the distributor sent me 4+1 instead of 3+2 like I ordered. and I didn't want to have to pay the freight back. normal price for these rims are $140 each if quadcustoms doesn't want this set then they are yours but I have to have freight added.

[Silverfox@C&DRacing]

Originally posted by quadcustoms
ill take them for 250 shipped to tennessee

615 476 4134 for my card info im david

I need to add freight to these because I priced them as low as I could, if I pay for the freight I am in the hole.