Best method for Grip installation

[TDBRPH]

I have heard many different ways but I was curious what the most popular method is ie... glue or no glue wire or no wire etc...

I will be putting spider grips on Tag T2 bars.

Thanks
Triston

[Sportrax10]

I usually use wd 40 to get the grip on, then use safety wire.. and let it dry and I dont have problems... Just as long as you use safely wire...

[Cole Trane]

A little bit of soap and water. Or you can use grip glue. I don't always use safety wire though, only if it's loose.

[wyndzer]

3M weatherstrip adhesive. Works like a charm and the grips don't budge. Thank Jeff@quadshop for this info.

[400-416EX]

I have used aresol hairspray or spray paint

[boogiechile]

I have been using 3M weathersrtip adhesive for 15 years now. It works pretty good but I have had it slip loose two times over all those years. Not too bad.

[XANDADA]

I just wet it with a little straight water and muscle it on. I tried soapy water once and it was a lot easier to get on but every time it was wet out they would move. Now its just straight water and it never moves...

honda grip glue & slide it on & let it sit for 24 hours

[ZRider400]

i use grip glue....slide the grip on, let it try then put wire on it.

[Florida400EX]

Why bother payin an extra $10 for a tube of grip glue that says Honda. Just buy some grip glue at your local shop.

[TDBRPH]

Thanks for all the tips.... Guess I will just pick a method and roll with it !!

Triston

[250rmike]

i like to use safty wire grip glue is to much of a pain to get back off when you need to put new grips on cause you have to cut the grips off then there is usually some grip still on that you have to scrape off

[JDiablo]

wd-40 or hairspray....and after im done,i hook up my small compresser and shoot air underneath the grips...keeps them rock solid....you learn alot from chilling at a bike shop where your friend works:D

[JDiablo]

wd-40 or hairspray....and after im done,i hook up my small compresser and shoot air underneath the grips...keeps them rock solid....you learn alot from chilling at a bike shop where your friend works:D

i get my honda grip glue for free

[TC426EX]

Honda grip glue.... Youll have to cut the grips off when you want to change it sticks so good....

[K_Fulk]

Originally posted by wyndzer
3M weatherstrip adhesive. Works like a charm and the grips don't budge. Thank Jeff@quadshop for this info.

I took this advise last week. Works great. And like Jeff said its the same stuff as the honda.

[K_Fulk]

Originally posted by wyndzer
3M weatherstrip adhesive. Works like a charm and the grips don't budge. Thank Jeff@quadshop for this info.

I took this advise last week. Works great. And like Jeff said its the same stuff as the honda.

[400racer1412]

go get scott grip glue then get some zip ties and put the glue on and then zip tie the grip really really hard and then wait like over night and then take the zip ties off and then for dafty wire jsut take a pipe cleaner and bearn off all the fuzzy suff



______________________
red 400ex
cut fenders
itp rims
kenda scrorpion
dg nerfs
oneal bars
scott grips
kandn air filter

[KY Woods Rider]

Here's my method... http://www.geocities.com/born2bwild81/ChadsATVpage_gripinstall.html

[QuadRacer041]

Originally posted by 400-416EX
I have used aresol hairspray or spray paint


thats what i use too works like a charm

[TDBRPH]

Great info thanks everyone........

[hondarider2006]

throw some grip glue on the bar....than put the grip on really fast.


Spray the handle bar with brake clean(where the grip is gonna be) and slid the grips on. Let them sit for a little while, and they won't go anywhere;)

[markk]

Im running tag t-2's and i used to run glue, but i decided that if i use saftey wire glue is just a waste of money, So i use three rings of saftey wire on each grip and iv never had a problem!!!!!