Made some new foot pegs

[EXJUMPER]

Hope the pics work. What do you think?
http://images.ofoto.com/photos649/1/26/75/27/4/4/404277526103_0_ALB.jpg

[EXJUMPER]

2
http://images.ofoto.com/photos649/1/26/75/37/2/3/302377526103_0_ALB.jpg

[EXJUMPER]

http://images.ofoto.com/photos649/1/26/75/27/10/3/310277526103_0_ALB.jpg

[EXJUMPER]

They are not painted yet, but I think they turned out ok.

[EXJUMPER]

Might need to open one up in a new window to get them to work.

[Woodsrider]

Not bad. Whats the material? Is it stainless? How thick?

Slap some PC on them and get em mounted up and do some feild testing;)

[JOEX]

Look good:) Powdercoating might be better than painting;)

How are they going to be mounted? The mounting plate doesn't look big enough in the pics.:confused:

[EXJUMPER]

They bolt in the factory holes and the top of the peg sits about 1/8" lower than stock. As far as material goes, the mounting plate is 1/4" steel and the pegs are 1/8" flat stock.

[400ex28]

good job looks cool

[EXJUMPER]

Thanks for the replys guys!:macho

[sickmojave]

is it just me that can't see the pictures??:confused:

[JRDrider22]

i cant see them either

[member]

i cant see them either:(

[member]

ok nvm i got it to work, i just right clicked the red x went to properties then copy the url and pasted it into the address box or w/e and after that it just worked, btw lookin good mani like the way they look right now, why change them?

[EXJUMPER]

I don't plan to change them. I'm just going to powder coat them so they don't rust.;)

[sickmojave]

Originally posted by member
ok nvm i got it to work, i just right clicked the red x went to properties then copy the url and pasted it into the address box or w/e and after that it just worked, btw lookin good mani like the way they look right now, why change them?

that worked for me to thanks.


NICE footpegs :eek2:

[Cody_300ex]

Nice pegs man!!! those are awesome lookin! I would PC them tho.

[JDiablo]

only the first pic worked for me,but from what i see,they dun look to shabby....two thumbs up:cool:

[toby400ex]

How much would ya build me some for?:p

[EXJUMPER]

You have PM.:cool:

[tore up]

how much for a set?

[member]

how did you cut them out?

[exrider360]

nice job how long did it take

[EXJUMPER]

Originally posted by member
how did you cut them out?

Sat down with some graph paper and drew them actuall size. Then took all the measurements and transfered it to a 1/8 piece of hardboard. I drilled 3/64" holes in the hardboard where the holes would be drilled so when I laid the hardboard down on the steel plate I could trace the design and put little dots where all the holes had to be drilled. I tacked the three plates together and drilled them all out at once, then I used a cut off wheel to cut out the plates. Did the same thing with the brackets. If you want to see the template I made let me know and I will take a pic of it and post it on here.

[EXJUMPER]

Originally posted by exrider360
nice job how long did it take

I have about four hours in them.

[300exPat]

id like to see those templates you used if you don't mind


If you want to see the template I made let me know and I will take a pic of it and post it on here.