post your Graphics

[dirtriderex]

I wanna get some graphics but I don't know where to start. Also I'ev seen budweiser dirtbike graphics, can anyone find them for a 450r

Click on the link in my signature.

[dirtriderex]

Nice quad:D very tight

[Sportrax10]

http://www.imagestation.com/picture/sraid116/pbdfecc42f86c31c430195dc649f9477c/f8a5ca7a.jpg

K&K graphics...

[r450rr]

i havbe to say those k and k graphics are sweet.. i got me a set on the way just ordered them today:p

[HoNdA_4FiDdY_R]

Where did u get those Woody graphics? How much?

[r450rr]

um this might be alittle to late because my kandk's are supposed to be here anyday, but how much is the original graphics for the 450r, just incase the kandk's buble so bad that i dont like them anymore and decide to go back to original.. but they prolly wont just would like to know , thanks

[mascman]

Are there any other graphics available besides the K&K?

They look OK, but that's the only ones you see. I'd like to see a variety to pick from.

[dirtriderex]

Yeah there has to be more than that.

[TrX450rKiD]

These are nice...

http://www.oneindustries.com/quad_img/ho_trx450r_grhotr7_lrg.jpg

I got my number plates and Woody graphics @ www.BRMoffroad.com I paid $30.00 for the Woody decals.

[mascman]

Those are nice...looks like One Industries.

[TrX450rKiD]

Those are One Industries ;)

I like them because they continue onto the scoop below the front fenders. Another reason I think the look so nice is because when they end, it is not a very drastic change like the K+K (don't get me wrong...those are my 2nd favorite graphics) :cool:

[mjtwvc]

Originally posted by r450rr
um this might be alittle to late because my kandk's are supposed to be here anyday, but how much is the original graphics for the 450r, just incase the kandk's buble so bad that i dont like them anymore and decide to go back to original.. but they prolly wont just would like to know , thanks

hey heres a little trick for applying graphics,vinyls or stickers all about the same to apply use a spray bottle with just a touch of dish soap and give your graphics a mist dont soak them and this will help in pushing the bubbles out from under the graphics also spray the outside before trying to work them it will allow you to push a little harder without scratching or tearing your graphics .
the water will evaporate once the sun gets on it for a while and if you have tiny little bubbles thats most likely the water and will evaporate . if you mist them before applying and you happen to f***up youll have a better chance of lifting it up and trying again.
and if you have a bubble that you cant seem to get out ( be sure not to streach the vinyl or graphic cause then your screwed)take
a needle or xsacto knife and just make a tiny hole as where you will then push the air out. also you can use your blow dryer to help warm them and get the smaller bubbles out or just to help it stick.

well thats my two cents on how to apply graphics
been doing it for years but much larger scale( some tiny crap two)

GOODLUCK:D

[250EXking]

Man them K&K graphics are smoking man. NIce:)

[300racer]

do you know how much the one industries cost? I like the kandk graphics but it seems that alot of people have them. the one industries I haven't seen anywere and they look awsome also

[Quadaholic]

N-style has released their Hot Wheels Replicas for the 450R. They look pretty good, should be ready for shipment mid-May. Throttle Jockey should have their Woody grafx ready pretty quickly also.