yamablaster24
05-07-2004, 04:21 PM
This Atv was bought to be a trail rider but now i am looking for a full on Mx racer. I have rode other blasters and other quads and this one is untouchable. It has been very reliable and has a very strong motor. Almost all of the parts have been redone and has minimal Scratches from getting on and off the quad. Wether you are looking to get a trail quad, race quad, or something to ride around the woods, this Atv is perfect.I love it but i have a real good deal on a mx racing ATV and need to sell this. New parts/Mods are as follows.This ATV is ready to ride and is sold As is with no warranty.The plastics and seat cover are painted with plastic or vinyl paint and I used primer and it is holding good. Hubs are also painted metallic green and wheels are painted also
-Whole motor redone by yamaha dealership, all seals and bearings replaced,crank redone, all reciepts-cost over $750.00(MOTOR is very dependable now and should last a while(all done december of 2003)
-Cylinder bored .50mm over with WSM Aluminum Piston
-Transmission In excellent condition.
-New chain+ sprockets.
-Some New bushings and bearings
-FMF FATTY expansion chamber and FMF POWERCORE II silencer(aftermarket muffler and pipe)
-Keihin 30mm PWK carburator jetted professionally
-K+N Air Filter
-Trenga racing Intake
-unreliable oil injection removed,always use Klotz R50 oil with premium gas mixed 32:1
-Boyesen reeds, reeds spacer
-Cut fenders
-Polished parts of motor and throttle cover
-Alloy aluminum Handlebars with Spider Grips
-Front wheel spacers
-ac alloy nerf bars(very good to protect feet)
-new ignition coil
-20 inch ITP blackwater tires in back and Stock tires in front-both in good condition,no holes or patches
-Full Belly skid plates for extra protection to frame
-Modified front Bumper
-Many Painted Parts
-Motor has no leaks at all, very sound
lots,lots more just email me at yamablaster@hotmail.com or aim yamablaster024
NEED TO GET $1500 OUT OF THIS FOR A DOWN PAYMENT ON MY MY MX BLASTER
http://img36.photobucket.com/albums/v110/yamablaster024/D053.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/5.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/6.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/4.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/2.jpg
EXTRA PARTS.....WORK FINE :tup:
http://img36.photobucket.com/albums/v110/yamablaster024/1.jpg
-Whole motor redone by yamaha dealership, all seals and bearings replaced,crank redone, all reciepts-cost over $750.00(MOTOR is very dependable now and should last a while(all done december of 2003)
-Cylinder bored .50mm over with WSM Aluminum Piston
-Transmission In excellent condition.
-New chain+ sprockets.
-Some New bushings and bearings
-FMF FATTY expansion chamber and FMF POWERCORE II silencer(aftermarket muffler and pipe)
-Keihin 30mm PWK carburator jetted professionally
-K+N Air Filter
-Trenga racing Intake
-unreliable oil injection removed,always use Klotz R50 oil with premium gas mixed 32:1
-Boyesen reeds, reeds spacer
-Cut fenders
-Polished parts of motor and throttle cover
-Alloy aluminum Handlebars with Spider Grips
-Front wheel spacers
-ac alloy nerf bars(very good to protect feet)
-new ignition coil
-20 inch ITP blackwater tires in back and Stock tires in front-both in good condition,no holes or patches
-Full Belly skid plates for extra protection to frame
-Modified front Bumper
-Many Painted Parts
-Motor has no leaks at all, very sound
lots,lots more just email me at yamablaster@hotmail.com or aim yamablaster024
NEED TO GET $1500 OUT OF THIS FOR A DOWN PAYMENT ON MY MY MX BLASTER
http://img36.photobucket.com/albums/v110/yamablaster024/D053.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/5.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/6.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/4.jpg
http://img36.photobucket.com/albums/v110/yamablaster024/2.jpg
EXTRA PARTS.....WORK FINE :tup:
http://img36.photobucket.com/albums/v110/yamablaster024/1.jpg