rs500r
04-28-2004, 10:08 PM
i have quad that i havn't finished and might part out. so make me some offers. please don't offer if not serious. i won't part out if people mess with me. i'll try list as much as i can. my phone number is 515-306-4283. randy 86 frame been powdercoated siver vein.
lonestar a-arms +2+1 black silver vein
w/ ball joints
+2 tie-rods
lonestar -1 swingarm all lonestar parts are mounted but
lonestar carrier not used. new
lonestar axle +4
lonestar anti-fade
lonestar micro lite rear hubs
front and rear elka zero preload shocks, fronts have been on my sons r for 4 to 5 hrs. rear brand new, mounted but not used, valved for 200lbs +2. fronts are piggyback.
used nacs hubs with collars for 400ex or 89 250r spindle,
collars are not in hubs right now. i would rate the hubs a 8 of 10. they have silver caps. and wave rotors
brand new rear maier red plastic, used front one piece but very nice, front shows wear where the legs rub. but i have a brand new blue k&k flame graphics, it covers the part that was rubbed by legs, seat will go with because it has k&k cover.
brand new mounted roll design +1 stem with anti-vibe
tag t-2's cr high, brand new
motor i purchased off legacy, its a brand new, i believe its 85 atc, its black with esr red clutch cover and water pump cover, and esr 500.00 cr ignition motor had never been fired but i had wiesco piston and mild mx port. the cylinder had some rust from moisture from sitting so long.
38mm air styker, brand new in box
v-force reeds very close to new, he said they were brand new.
new rear wave rotor.
front and rear ultimate billet beadlocks, rears have brand new rings, polished and look super great, 9x8, fronts are polished to look very nice too, rings have scratches but no dents, they are 10x6.
i don't have pics right now i'm sorry.
that's it for now. i'm not sure what i'm going to do but will know by next week sometime. thanks for looking
lonestar a-arms +2+1 black silver vein
w/ ball joints
+2 tie-rods
lonestar -1 swingarm all lonestar parts are mounted but
lonestar carrier not used. new
lonestar axle +4
lonestar anti-fade
lonestar micro lite rear hubs
front and rear elka zero preload shocks, fronts have been on my sons r for 4 to 5 hrs. rear brand new, mounted but not used, valved for 200lbs +2. fronts are piggyback.
used nacs hubs with collars for 400ex or 89 250r spindle,
collars are not in hubs right now. i would rate the hubs a 8 of 10. they have silver caps. and wave rotors
brand new rear maier red plastic, used front one piece but very nice, front shows wear where the legs rub. but i have a brand new blue k&k flame graphics, it covers the part that was rubbed by legs, seat will go with because it has k&k cover.
brand new mounted roll design +1 stem with anti-vibe
tag t-2's cr high, brand new
motor i purchased off legacy, its a brand new, i believe its 85 atc, its black with esr red clutch cover and water pump cover, and esr 500.00 cr ignition motor had never been fired but i had wiesco piston and mild mx port. the cylinder had some rust from moisture from sitting so long.
38mm air styker, brand new in box
v-force reeds very close to new, he said they were brand new.
new rear wave rotor.
front and rear ultimate billet beadlocks, rears have brand new rings, polished and look super great, 9x8, fronts are polished to look very nice too, rings have scratches but no dents, they are 10x6.
i don't have pics right now i'm sorry.
that's it for now. i'm not sure what i'm going to do but will know by next week sometime. thanks for looking